Wear Resistant Steel Plate Specification | |
| DIN: XAR300,XAR400, XAR450, XAR500, XAR600, DILLIDUR400V,DILLIDUR450V,DILLIDUR500V; X120Mn12; 1.3401; |
Thickness | 2-300mm (2-100mm usually used) |
Width | 1000-3000mm (1000-2200mm usually used) |
Length | 1000-12000mm or as your request |
Application | Widely used in a variety of architectural and engineering structures,such as |
Wear Resistant Steel Plate Chemical Composition and Mechanical Properties | ||||||||||||
Chemical Composition(Max) | ||||||||||||
Material | C | Si | Mn | P | S | Cr | Ni | Mo | Ti | Bt | Als | CEV |
NM300 | 0.23 | 0.70 | 1.60 | 0.025 | 0.015 | 0.70 | 0.50 | 0.40 | 0.050 | 0.0005-0.0006 | 0.010 | 0.45 |
NM360 | 0.25 | 0.70 | 1.60 | 0.025 | 0.015 | 0.80 | 0.50 | 0.50 | 0.050 | 0.0005-0.0006 | 0.010 | 0.48 |
NM400 | 0.30 | 0.70 | 1.60 | 0.025 | 0.010 | 1.00 | 0.70 | 0.50 | 0.050 | 0.0005-0.0006 | 0.010 | 0.55 |
NM450 | 0.35 | 0.70 | 1.70 | 0.025 | 0.010 | 1.10 | 0.80 | 0.55 | 0.050 | 0.0005-0.0006 | 0.010 | 0.60 |
NM500 | 0.38 | 0.70 | 1.70 | 0.020 | 0.010 | 1.20 | 1.00 | 0.65 | 0.050 | 0.0005-0.0006 | 0.010 | 0.65 |
NM550 | 0.38 | 0.70 | 1.70 | 0.020 | 0.010 | 1.20 | 1.00 | 0.70 | 0.050 | 0.0005-0.0006 | 0.010 | 0.72 |
NM600 | 0.38 | 0.70 | 1.90 | 0.020 | 0.010 | 1.50 | 1.00 | 0.70 | 0.050 | 0.0005-0.0006 | 0.010 | 0.76 |
Material | Tensile MPA | Elongation % | Impact energy -20ºC | HBW | ||||||||
NM300 | ≥1000 | ≥14 | ≥24 | 270-300 | ||||||||
NM360 | ≥1100 | ≥12 | ≥24 | 330-390 | ||||||||
NM400 | ≥1200 | ≥10 | ≥24 | 370-430 | ||||||||
NM450 | ≥1250 | ≥7 | ≥24 | 420-480 | ||||||||
NM500 | ≥1250 | ≥7 | ≥24 | ≥470 | ||||||||
NM550 | ≥1250 | ≥7 | ≥24 | ≥530 | ||||||||
NM600 | ≥1250 | ≥7 | ≥24 | ≥570 | ||||||||
Grade | C | Si | Mn | P | S | Cr | Mo | Cu | Ni | B | ||
XAR400 | 0.20 | 0.80 | 1.50 | 0.025 | 0.010 | 1.00 | 0.50 | -- | -- | 0.005 | ||
XAR450 | 0.22 | 0.80 | 1.50 | 0.025 | 0.012 | 1.30 | 0.50 | 0.30 | -- | 0.005 | ||
| 0.28 | 0.80 | 1.50 | 0.025 | 0.010 | 1.00 | 0.50 | -- | -- | 0.005 | ||
| 0.40 | 0.80 | 1.50 | 0.025 | 0.010 | 1.50 | 0.50 | -- | 1.50 | 0.005 | ||
Grade | Yield Strength | Tensile Strength | Elongation | BH | ||||||||
XAR400 | 1150 | 1300 | ≥12 | 360-440 | ||||||||
XAR450 | 1200 | 1350 | ≥10 | 410-490 | ||||||||
XAR500 | 1500 | 1600 | ≥9 | 450-530 | ||||||||
XAR600 | -- | -- | -- | ≥550 | ||||||||
Material | C | Si | Mn | P | S | Cr | ||||||
Mn13 | 1.1~1.3 | 0.3~0.5 | 12~13 | ≤0.100 | ≤0.040 | ≤1.5 | ||||||
X120Mn12 | 1.1~1.3 | 0.3~0.5 | 12~13 | ≤0.100 | ≤0.040 | ≤1.5 | ||||||
1.3401 | 1.1~1.3 | 0.3~0.5 | 12~13 | ≤0.100 | ≤0.040 | ≤1.5 | ||||||
SCMnH11 | 0.9~1.5 | 0.3~1.0 | 10~15 | ≤0.100 | ≤0.050 | ≤1.5 | ||||||
ASTM A128 | 1.1~1.3 | 0.3~0.5 | 12~13 | ≤0.100 | ≤0.050 | ≤1.5 |